Doepfer A-100Ad5

()

Vis oversættelse

5V Low-cost adapter

Plug adapter for +5 V / 100 mA
Can be used in place of a 5 V power supply
For Doepfer modules requiring +5 V: e.g. the A-113,190 or 191
Can be plugged into a free socket on the bus board
The current is taken from the 12 V supply

30 dages-Money Back garanti

3 års Thomann garanti

Fås siden Januar 2004
Artikelnummer 166503
salgsenhed 1 stk
Description Electronic Component

137 kr

Alle priser inkl. moms

188

Salgsrang

i Andet tilbehør til synthesizere

Kunder som så på dette produkt købte dette

Korg Nu:Tekt NTS-2 Oscilloscope

1.218 kr

købt

Roadworx Synthesizer Stand

222 kr

købt

thingyfab Stand Behringer Crave / TD3

333 kr

29 Kundebedømmelser

5 23 Kunder 4 5 Kunder 3 1 Kunde 2 0 Kunder 1 0 Kunder

4.8 / 5

forarbejdning

Retningslinjer for anmeldelser

16 Anmeldelser

Vis oversættelse

Vis original

Der opstod en fejl. Prøv igen senere.

May the force be with you... exactly 5 volts.

Stephen662 15.07.2013

Needed this to supply 5 volts to some of the modules in my Doepfer case. Yes, some modules (usually logic modules) need 5v to work, and this is what you need.

Simply plugs into the rail that you need to supply the 5v on - if you have 5v modules all over your rack you will need to instal one on each rail as required. Job done. Works a treat.

Anmeld bedømmelse

Synes du at denne vurdering er forkert eller af en anden grund ikke læselig? Vær venlig at skrive i det følgende kommentarfelt hvorfor og hvis muligt din email-adresse, så vi kan give dig en tilbage melding til din kommentar.

Vis oversættelse

Vis original

Der opstod en fejl. Prøv igen senere.

You might not think you need this but you probably will

Anonym 20.01.2016

This little adaptor will allow you to run anything which requires a +5v power supply on one power rail of your modular case. I bought it because it was required for an oscillator which I purchased, but it can have many applications. My next use for it will be to power LED lights to illuminate my modular in gig situations. You simply connect the adaptor to a spare connector on the rail which you will need it, and then you have +5v power available for all the other connectors on that rail. My one reservation is that this could have been a little bit cheaper for what it does, or alternatively Doepfer could just build this provision into their modular cases as standard. After all a P9 case, for example, is not cheap and when you have spent that amount of money you kind of resent having to buy this.

Anmeld bedømmelse

Vis oversættelse

Vis original

Der opstod en fejl. Prøv igen senere.

Andrew463 06.12.2014

Tough one to rate as it's just a plug... but if you have products from Mutable Instruments and others that require 5-Volt power it's a necessity for a Doepfer rack. It couldn't be any simpler to use, just plug it in and away you go.

Again, good value too.

Anmeld bedømmelse

Vis oversættelse

Vis original

Der opstod en fejl. Prøv igen senere.

Get it for those hungry modules.

Harry Turner 02.11.2019

The Sub Harmonic Generator requires this.

Anmeld bedømmelse

Læs alle anmeldelser

Doepfer A-100Ad5

5V Low-cost adapter

5V billig adapter

Kunder som så på dette produkt købte dette

29 Kundebedømmelser

Du skal være logget på, for at kunne vurdere et produkt.

16 Anmeldelser

Smart Navigator

Serveret med kærlighed!

Doepfer A-100Ad5

5V Low-cost adapter

5V billig adapter

Kunder som så på dette produkt købte dette

Tilbehør og matchende produkter

29 Kundebedømmelser

Du skal være logget på, for at kunne vurdere et produkt.

16 Anmeldelser

Sammenlign valgmuligheder

Smart Navigator