Göldo MB05C Adapter Bushings

()

Start 360°

Vis oversættelse

Adapter Bushings for Machine Heads

Makes it possible to mount vintage-style machine heads with a shaft diameter of 6.4 mm in a bore hole for enclosed machine heads of 10 mm
6 Pieces
MB05C
Surface: Nickel

30 dages-Money Back garanti

Fås siden Juli 2006
Artikelnummer 193586
salgsenhed 1 stk

69 kr

Alle priser inkl. moms

Salgsrang

i Andre reservedele

Kunder som så på dette produkt købte dette

Harley Benton Parts Copper Shielding Tape

38 kr

købt

TAD Cap Orange Drop 22nF 100V

Mojotone Treble Bleed Mod

37 kr

177 Kundebedømmelser

5 130 Kunder 4 27 Kunder 3 14 Kunder 2 3 Kunder 1 3 Kunder

4.6 / 5

forarbejdning

Retningslinjer for anmeldelser

88 Anmeldelser

perfect and simple solution

delpino 29.10.2021

I wanted locking tuners for my LP but there wasn't any combination that fit my guitar (vintage dimensions with two screws and 10mm bore hole). These adapters solved the problem, look great and for a reasonable price. What else can one ask for?

Anmeld bedømmelse

Synes du at denne vurdering er forkert eller af en anden grund ikke læselig? Vær venlig at skrive i det følgende kommentarfelt hvorfor og hvis muligt din email-adresse, så vi kan give dig en tilbage melding til din kommentar.

Passer perfekt

BorisSGD 06.06.2023

Perfekt til at lave standard hullerne i din guitar om til Vintage størrelse.

Anmeld bedømmelse

Vis oversættelse

Vis original

Der opstod en fejl. Prøv igen senere.

My bad, they didn’t fit…

tremblox 07.01.2023

These are fine but didn’t fit my application. I’m writing this as a heads-up to others.
Firstly not all tuners, even Gotoh tuners have the same post/shaft diameter. Not even in the same series. Take for example the Kluson-style SD91 series. The units with magnum lock and height adjustable post/shafts - the HAP-M units - have 6mm post diameters. They fit too loosely in these bushings and as a result of the string tension the tuners will get sloppy and wear out prematurely over time.
On the other hand the standard SD91 tuners (no locking, height adjustment) have post diameters of ca 6,25mm (from memory so I might be off by a tad), so that these bushings will be a perfect fit and you’ll enjoy a lifetime of happiness with them.

So in all cases the buyer should check their post diameters carefully before selecting and trying to source the correct bushings. Take care, it’s a jungle out there.

Anmeld bedømmelse

Vis oversættelse

Vis original

Der opstod en fejl. Prøv igen senere.

Great product - Just not the right fit

Tiago Oliveira Coelho 21.07.2020

Bought a set of Klusons for my Classic 60's Tele (MIM) to replace the Kluson-style Ping/Fender stock tuners, but the bushings were too narrow for the pre-existing holes. So I found these conversion bushings and thought my problem was solved.
Before anything, I have to say that they're quite good, and feel very solid. A+ for building quality.

However, the holes for the tuners in my guitar is neither 8mm nor 10mm. If you have the same model as I do, either be prepared to enlarge the holes on the headstock to fit these, or just use aluminium tape on the narrow bushings to keep them in place.

Anmeld bedømmelse

Læs alle anmeldelser

Göldo MB05C Adapter Bushings

Adapter Bushings for Machine Heads

Adapterbøsninger til mekanikerhoveder

Kunder som så på dette produkt købte dette

177 Kundebedømmelser

Du skal være logget på, for at kunne vurdere et produkt.

88 Anmeldelser

Smart Navigator

Serveret med kærlighed!

Göldo MB05C Adapter Bushings

Adapter Bushings for Machine Heads

Adapterbøsninger til mekanikerhoveder

Kunder som så på dette produkt købte dette

Tilbehør og matchende produkter

177 Kundebedømmelser

Du skal være logget på, for at kunne vurdere et produkt.

88 Anmeldelser

Sammenlign valgmuligheder

Smart Navigator